Influence of lanthanum on enhancement of mechanical and electrical properties of Cu-Al_2O_3 composites

Two kinds of Cu-Al_2O_3 composites(with and without La) were prepared via mechanical alloying-spark plasma sintering(MA-SPS) method. Microstructure, mechanical properties and electrical resistivity were investigated systematically using metallography, scanning electron microscopy, transmission electron microscopy, mechanical and electrical properties testing. The results indicate that an appropriate amount of La can homogenize the distribution of Al_2O_3. As such, yield strength, ultimate tensile strength and elongation of Cu-Al_2O_3-La are greatly increased. Some semi-coherent interface between Cu and Al_2O_3 is found, which means a low interface energy. The grain shape of Cu changes to irregular band with the addition of La. This change results in a density decrease of grain boundary and reduces electrical resistance. Lanthanum may exist in the form of La_2O_3.     

Wear mechanism of a novel AlSiMgAl2O4Al2O3 composite used in the low vessel of an RH secondary refining furnace

A novel AlSiMgAl₂O₄Al₂O₃ composite brick was prepared and evaluated in the low vessel of an RH (the initials of Ruhrstahl and Hereaeus) secondary refining furnace; it was characterized by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The results show that after use, the AlSiMgAl₂O₄Al₂O₃ composite has a functional gradient with an erosion zone–reinforced zone–original zone phase distribution, in which the phases in the erosion zone (0–1.8?cm) are a Mg-hercynite spinel solid solution, α-Al₂O₃, and minor amount of Al₃Fe₅O₁₂. Furthermore, the phases in the reinforced zone (1.8–5.0?cm) are γ-AlON, 21RSiAlON, SiC, Mg_0.388Al_2.408O₄, and α-Al₂O₃; i.e., the Al and Si in the composite are completely converted into non-oxide reinforced phases. Finally, the phases in the original zone (>5.0?cm) show no change. The reaction mechanism is as follows. During operation, a Mg-hercynite spinel solid solution is formed in the erosion zone due to a reaction between MgAl₂O₄ and FeO from a refinery operation. Therefore, the slag erosion of the material is improved. The Al and Si metals undergo active oxidation, and 21RSiAlON flakes are subsequently formed from the products of the metastable Al₂O(g), SiO(g), and N₂(g) in the ambient. The γ-AlON is formed by a carbothermal reduction nitridation of the α-Al₂O₃ and residual active carbon from the resin binder. The 21RSiAlON and γ-AlON reinforce the composite brick and improve its high temperature performance accordingly. Its service life is 110% that of the magnesia-chrome bricks used in the same period. The reaction model was also established.     

不同硫组分在菱锌矿表面吸附的计算研究

采用量子化学计算的第一性原理模拟了不同硫组分在菱锌矿(001)解离面上的吸附,研究了硫组分在菱锌矿表面的吸附机理。吸附能计算结果显示:相比HS-,S2-在菱锌矿(001)解离面的吸附更加稳定,吸附能的绝对值更大,同时发现硫组分主要吸附在Zn位上;吸附前后的态密度对比分析表明,硫组分在菱锌矿表面的吸附形成了新的Zn—S化学键;布居分析发现:硫组分吸附在菱锌矿表面新形成Zn—S键的过程中,Zn、S之间发生了明显的电荷转移。研究结果阐释了菱锌矿的硫化机理,为菱锌矿硫化浮选研究提供了理论依据。     

Self-consistent kinetic theory with nonlinear wave-particle resonances

We have developed, based on the oscillating-center transformation, a general theoretical approach for self-consistent plasma dynamics including, explicitly, effects of nonlinear(higherorder) wave-particle resonances. A specific example is then given for low-frequency responses of trapped particles in axisymmetric tokamaks. Possible applications to transport as well as nonlinear wave growth/damping are also briefly discussed.     

芽孢杆菌Bacillus sp.dwc-2对模拟地下水中U(Ⅵ)的还原行为研究

在厌氧条件下研究了西南地区一种典型土壤微生物芽孢杆菌Bacillus sp.dwc-2对模拟地下水中U(Ⅵ)的还原行为，重点考察了时间、无机阴离子、腐殖酸（HA）及富里酸（FA）对还原的影响，并利用TEM、EDS、SAED和XPS对还原后的样品进行了表征。结果表明：在pH=7.0、c_NaHCO3=5 mmol/L和T=303 K条件下，Bacillus sp.dwc-2对U(Ⅵ)的还原率随时间的增加而增加，24 h内最大还原率为12.2%，此后则随时间的增加逐渐降低；HA和FA对U(Ⅵ)的微生物还原行为有一定影响，其中HA和FA浓度为25 mg/L时，U(Ⅵ)的还原在24 h最明显，其还原率分别为14.2%和16.2%，但随着HA和FA浓度的继续增加，因在U(Ⅵ)离子与HA、FA形成的配合物表面形成致密的腐殖层，抑制了电子的转移，阻止了U(Ⅵ)的还原。此外，研究表明HCO₃^-也会抑制U(Ⅵ)的还原。TEM-SAED和XPS分析证实了还原过程中U(Ⅳ)的存在。上述结果可为真实环境中微生物还原U(Ⅵ)提供基础数据和参考。     

纸基底印刷无芯片RFID湿度传感器* .txt

摘要：提出了一种基于纸基底的喷墨印刷无芯片RFID湿度传感器，通过遗传算法与射频仿真软件HFSS相结合，对常规开口环谐振器结构进行分布式加载，得到目标频率为245 GHz的谐振特性良好的传感器模型；采用DMP3000型材料打印机，在不同纸基底上喷墨印刷银墨水制作传感器，以纸张本身的吸水性实现湿度传感；研究不同纸基底对湿度传感器感湿灵敏度和恢复度的影响。结果表明，柯达相纸传感器的灵敏度最高，高湿灵敏度可达到8 MHz%RH，双铜纸湿度传感器恢复度高且恢复时间短，仅为2 min；两种基底湿度传感器皆有较好的一致性、中长期稳定性，且湿敏特性在20℃～30℃范围内受温度影响较小。对纸基湿度传感器的感湿机理进行了分析，纸主要成分纤维素表面的羟基与吸附的水分子作用形成氢键，改变了基底的介电参数，传感器的湿敏特性与纸的成分和结构有关。 .txt     

Gel-casting of transparent magnesium aluminate spinel ceramics fabricated by spark plasma sintering (SPS)

In this paper, a transparent magnesium aluminate spinel ceramic was fabricated through the newest colloidal gel casting method, using a synthetic powder with the average particle size of 90 nm and Isobutylene-Maleic Anhydride (ISOBAM) additive. ISOBAM served as both a dispersant and a gelation agent to achieve a dense body. Also, the suspension rheological behavior was optimized by the solid loading of 85 wt%, the additive content of 0.7 wt%, and the gelation time of 350 s. This led to a green body with a density equal to 65% of theoretical density and the green strength of 14.48 MPa. The results revealed that the reduction of porosity and the uniform distribution of pores in the green body (smaller than half of the initial powder particle size, 35 nm), as accompanied by spark plasma sintering (SPS), resulted in the final body density of 99.97%, as well as the high in-line transmittance of 86.7% at the wavelength of 1100 nm.     

Loadbearing capacity of infill masonry walls considering the deformation‐based membrane effect

According to currently valid codes, it is not possible to determine the loadbearing capacity of unreinforced infill walls considering the deformation‐based membrane effect by incorporating the exact support conditions. One reason for this is the lack of a validated calculation procedure, which in addition to the equilibrium conditions also realistically represents the compatibility conditions of these systems. In the present paper, therefore, a new non‐linear analytical calculation procedure is presented. The main focus of the analysis of walls subject to area loading is the incorporation of the support conditions and thus the consideration of the deformation‐based membrane compressive force. Through generalised formulation and a standardised notation of the determination equations, different material behaviours and various support conditions can be taken into account with few parameters. On the action side, both lighter loading like wind loads and heavier loading like explosion loads can be considered. Through the implementation of the partial factor concept, it is possible to comply with the requirements of European codes and thus ensure the applicability of the analysis model.